Are you a big fucking moron idiot who gets their car into fights with the garage door? Of course you are! Don’t worry, I know the feeling.

Anyway, let’s get you back up and running with mirrors on both sides.

My car specifically is a 2007 BMW Z4 3.0si coupe. But I’m pretty sure these instructions will be the same for any first-gen Z4 or Z4M. 2009 and later models, I’m afraid you’re on your own!

If you’re lucky, you just twisted the mirror around and you can twist it back into shape. If the mirror assembly is still firmly attached to the body, you can try twisting it back the right way around and seeing if it locks back into place. There’s a stiff spring intended to resist this motion, so give it a good pull and twist. If it’s all flopping around, like mine was, you’re out of luck and will need to order a new part.

You can see the various options at RealOEM.com. My car does not have auto-dimming mirrors, nor do the mirrors fold, and I wanted the passenger side assembly, so my part number was 51167189708. Shopping around led me to GetBMWParts.com where I found the best price. Expect to pay a bit north of $200 for the part. After pulling out your credit card, spend a few minutes reminding yourself to be more fucking careful getting out of the garage next time, yeah?

The part that ships will be the whole assembly, including the painted shell. Except the shell you get won’t be painted, it’s just solid black. If your old shell is recoverable (mine was), you can take apart the old assembly and swap the shell onto the new one and avoid having to pay to have the new shell painted. The other possibly recoverable part is the mirror glass itself. Instructions for disassembling the old mirror follow after the door disassembly.

To get started, you’ll need a torx T10 and either a T15 or a T20 driver (I’ve forgotten); an approximately 6mm hex driver (again, I’ve forgotten the exact size); and some trim pry tool. A few other tools can come in handy, and I’ll mention them through the guide.

First, take off the mirror glass. If you can, tilt the mirror with the in-car controls to face downward. Along the top of the plastic behind the mirror is a notch, visible at the top of the following picture. When facing the mirror, you need to turn that notch to the left (counter-clockwise), for both the passenger and driver mirrors. This rotates the plastic circle on the back of the mirror from the locked position into the unlocked position. There’s some foam between the mirror and the servo that you may need to compress by pushing on the mirror to get the plastic circle to turn.

Z4 Mirror Locked

The above is an image of the mirror with the circle in the locked position, covering the tabs on the servo. Below is the unlocked position. It only turns a small amount. Notice the servo tabs are free in the below picture, which lets the mirror/plastic circle assembly come off of the servo.

Z4 Mirror Unlocked

Now let’s start taking the door apart so we can swap mirror assemblies.

Pop off the cap behind the door handle. I used a box cutter to pry the little bit of plastic off. BMW’s TIS says to use a piece of sticky weather trim tape to pull it out. Whatever. Take out the torx screw behind there.

Z4 Door Handle

Pry off the trim from the door grip with a trim removal tool (ten bucks at AutoZone, and way better than a screwdriver). Photo shows you where the clips are. Start from the bottom.

door_handle_trim

There are four screws back here, two small torx and large two hex-head screws. The lower screw had a bunch of noise proofing material stuck on it in my car. Pull the grip straight out from the door.

door_handle_back

Pop out the airbag label with your trim tool. There are three notches on each side. Under there should be another screw to remove. Try not to drop the screw into the door panel.

airbag_label

Next is the hard part, removing the door panel. The image below shows the clips that hold it onto the lower part of the door. I used the trim tool as a lever to get my fingers under, and then pried them out. I found it was easiest to start with a bottom corner and pop them out one by one. The top of the panel will still be attached to the door.

lower_door_clips

The upper clips were the hardest part of the whole process. The picture just below shows how they work. There’s a series of metal tabs which you can try to push down to release from the slots in the second picture below. You can also just use brute strength to pull them out. Good luck!

upper_clips_metal

upper_door_clips

I unplugged the speaker wire and the other wire over there, then rested the panel on the stacked blanket. Be sure to note where the speaker wire is plugged in before you unplug it! There are two identical slots, I’m not sure why.

Next take off the speaker next to the window. This is pretty easy, push in the top of the triangle and it will pop out, then pull the whole bit up and out. Unplug the speaker wire (screwdriver may help) and set it aside.

window_speaker

Unplug the wire that comes from the mirror assembly, and pull out the plastic clip from the door. Your new part should have this clip already on the wire, so don’t worry about recovering it. There are three silver torx screws back here which hold the mirror assembly onto the body. As you undo them, be sure to hold the mirror assembly so you don’t drop it down your door and onto the floor like a moron. After you get it off, you’ll have to squeeze the rubber plug through the hole to pull the wire out.

Next, it’s time to take the old assembly apart. If you’re not recovering any of the old parts, skip this.

There’s a handful of screws, thankfully all the same small torx screws. The first screw is on the bottom of the mirror, in a strip of black plastic. After the screw is out, pop off the little plastic bit that the screw went through.

Next, there are the three servo screws. With those out, you can unplug the servo and remove it. Finally, there are four screws through the plastic support into the shell. The shell is then held on with two clips on the outside of the mirror. Use a trim removal tool or something to pop out these clips. The shell should now be free.

Assembly is the reverse of disassembly. Thanks for reading!

No seriously, it’s pretty easy. Make sure to get the servo aligned correctly. On the passenger side, the two rectangular slots should face up and left. I’m not sure about the driver side.

servo

Unless you’re an idiot (hi!), put the whole mirror assembly back together before you put it on the car. Shove the cable through the hole and squeeze the rubber bit into its place. The slots for the silver screws on the new part aren’t threaded, so they’ll take some muscle to get in. Hook all the wires back up and make sure to slot the door handle cable into its holder on the door panel.

Attach the door panel to the door, starting with the top. I ended up basically holding the door and punching the door panel to get it onto the clips. Pop the bottom clips into place, and reassemble the trim.

Test out the speakers, window controls, lock controls, and mirror controls. If they’re all working, you’re done!

Did you find this helpful? Have any questions about the process? Want to share your own ran-the-car-into-the-house story? Leave a comment below!